Beijing IO controller B 9 2020-05-14 With this VSCP module it is possible to control up to ten digital IO channels where each can be configured as an input or an output. http://www.grodansparadis.com/beijing/beijing.html 8 Grodans Paradis AB

Brattbergavägen 17 Los 82770 Sweden

+46 8 40011835 Main Reception

support@grodansparadis.com

Support email

sales@grodansparadis.com

Sales inquires email

info@grodansparadis.com

General email

http://www.grodansparadis.com

Main web site Full manual for the Beijing module. Picture 1 of Beijing module. Picture 2 of Beijing module. Picture 3 of Beijing module. Picture 4 of Beijing module. Picture 5 of Beijing module. Picture 6 of Beijing module. Picture 7 of Beijing module. Picture 8 of Beijing module. Picture 9 of Beijing module. Picture 10 of Beijing module. Picture 11 of Beijing module. Picture of Beijing module connectors. Picture 12 of Beijing module. Picture 13 of Beijing module. Picture 14 of Beijing module. Picture 15 of Beijing module. Picture of Beijing module terminal block. Beijing schema for reversion B. Beijing PCB board layout for reversion B. Firmware for the Beijing I/O module with for use with the VSCP Bootloader wizard. Firmware for the Beijing I/O module with for use with the VSCP Bootloader wizard. Firmware version 1.1.0 for the Beijing module. Firmware version 1.0.0 for the Beijing module. Firmware version 1.1.0 for the Beijing module. 1 8 4096 Zone Zone this module belongs to rw Sub zone Sub zone this module belongs to rw Sub zone I/O 0 Sub zone for I/O channel 0 rw Sub zone I/O 1 Sub zone for I/O channel 1 rw Sub zone I/O 2 Sub zone for I/O channel 2 rw Sub zone I/O 3 Sub zone for I/O channel 3 rw Sub zone I/O 4 Sub zone for I/O channel 4 rw Sub zone I/O 5 Sub zone for I/O channel 5 rw Sub zone I/O 6 Sub zone for I/O channel 6 rw Sub zone I/O 7 Sub zone for I/O channel 7 rw Sub zone I/O 8 Sub zone for I/O channel 8 rw Sub zone I/O 9 Sub zone for I/O channel 9 rw I/O direction MSB Most significant part of I/O directions register. Set bit to zero for output and one for input.\n\n Bit 7 - Reserved.\n Bit 6 - Reserved.\n Bit 5 - Reserved.\n Bit 4 - Reserved.\n Bit 3 - Reserved.\n Bit 2 - Reserved.\n Bit 1 - Direction for I/O channel 9 - (RA0). 0=output. 1=input.\n Bit 0 - Direction for I/O channel 8 - (RA1). 0=output. 1=input.\n rw Direction 8 Direction for I/O channel 8 - (RA1). 0=output. 1=input. Direction 9 Direction for I/O channel 9 - (RA0). 0=output. 1=input. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. I/O direction LSB Least significant part of I/O directions register. Set bit to zero for output and one for input.\n\n Bit 7 - Direction for I/O channel 7 - (RA2). 0=output. 1=input.\n Bit 6 - Direction for I/O channel 6 - (RC7). 0=output. 1=input.\n Bit 5 - Direction for I/O channel 5 - (RC6). 0=output. 1=input.\n Bit 4 - Direction for I/O channel 4 - (RC5). 0=output. 1=input.\n Bit 3 - Direction for I/O channel 3 - (RC4). 0=output. 1=input.\n Bit 2 - Direction for I/O channel 2 - (RC3). 0=output. 1=input.\n Bit 1 - Direction for I/O channel 1 - (RB1). 0=output. 1=input.\n Bit 0 - Direction for I/O channel 0 - (RB0). 0=output. 1=input.\n rw Direction 0 Direction for I/O channel 0 - (RB0). 0=output. 1=input. Direction 1 Direction for I/O channel 1 - (RB1). 0=output. 1=input. Direction 2 Direction for I/O channel 2 - (RC3). 0=output. 1=input. Direction 3 Direction for I/O channel 3 - (RC4). 0=output. 1=input. Direction 4 Direction for I/O channel 4 - (RC5). 0=output. 1=input. Direction 5 Direction for I/O channel 5 - ((RC6). 0=output. 1=input. Direction 6 Direction for I/O channel 6 - ((RC7). 0=output. 1=input. Direction 7 Direction for I/O channel 7 - (RA2). 0=output. 1=input. I/O channel 0 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 1 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 2 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 3 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 4 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 5 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 6 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 7 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 8 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. I/O channel 9 status register Read or write the state of I/O channel 0 in this register.\n 0 - is returned for an inactive input or a low output. A written zero will set an output channel low.\n 1 - is returned for an active input or a high output. A written one will set an output channel high.\n rw Off Read: channel is in low state. Write: set output channel to its low state. On Read: channel is in high state. Write: set output channel to its high state. Output 0 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 1 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 2 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 3 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 4 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 5 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 6 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 7 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 8 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Output 9 control register The output control bits enable/disable intelligent functionality for a channel set as output.\n Bit 0 - Enable pulse.\n Bit 1 - If set: Alarm sent when protection timer triggers.\n Bit 2 - Protection timer enable.\n Bit 3 - Send On event when output goes to active state.\n Bit 4 - Send Off event when output goes to inactive state.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable output.\n rw Enable pulse Enable pulse on output Protection alarm If set: Alarm sent when protection timer triggers. Protection timer enable If set: Protection timer is enabled and will deactivate output channel when the timer times out. On event on activate enable If set: An on event will be sent when the output is turned on. Off event on deactivate enable If set: An off event will be sent when the output is turned off. Reserved Reserved Reserved Reserved Enable channel Set this bit to make the output controllable. Input 0 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 1 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 2 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 3 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 4 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode. Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 5 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 6 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 7 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 8 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Input 9 control register The input control bits enable/disable intelligent functionality for a channel set as input.\n Bit 0 - Send On/TurnOn event when input goes to active state.\n Bit 1 - Send Off/TurnOff event when input goes to inactive state.\n Bit 2 - 0 = Send On/off events. 1=Send turnon/turnoff events (if activated).\n Different meaning in button input mode where 0 = TurnOn and 1 = TurnOff.\n Bit 3 - Alarm event sent if input goes low.\n Bit 4 - Alarm event sent if input goes high.\n Bit 5 - Continuous alarm.\n Bit 6 - Activate Button imput mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated.\n Bit 7 - Enable input.\n rw Activate ON/TURNON-event Send On/TurnOn event when input goes to active state. Activate OFF/TURNOFF-event Send Off/TurnOff event when input goes to inactive state. State event select. Set to one to send turnon/turnoff events (if activated). Alarm on low An alarm event is sent if input goes low. Alarm on high An alarm event is sent if input goes high. Continuous alarm Alarm events are sent continuously while the state is active. Activate button input mode Activate Button input mode. Only TurnOff or TurnOn is sent when an input goes low and button input mode is activated. Which of them is sent is specified by bit 3 in the Input Control register. If it is set to 0 TurnOn is sent and if it is set to 1 TurnOff is sent. Enable input Set this bit to make the input active. Module Control register It is possible to control general module behaviour in this register.\n Bit 0 - Turn of input event repeat.\n Bit 1 - Reserved.\n Bit 2 - Reserved.\n Bit 3 - Reserved.\n Bit 4 - Reserved.\n Bit 5 - Reserved.\n Bit 6 - Reserved.\n Bit 7 - Enable weak pullups.\n rw Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Enable pullups Enable weak pullups if set to 1. Input stream sample time This is the time in seconds between input stream samples. Set to zero to disable.\n CLASS1.DATA is sent with data coding=0(bits), unit=0, sensor=0 for the inputs/outputs as set here. First byte is outputs, second byte is inputs. rw Debounce count This is the number of counts a button input signal should be low to be regarded as actice. Each count represents 10 ms. rw Short pulse duration This is the duration for the short pulse action. Each count represents 10 ms. A zero vaue gives a pulse that is the shortest possible. rw /////////////////////////////////////////////////////////////////////// // Register Page 1 - Timing /////////////////////////////////////////////////////////////////////// // * * * Pulse time * * * Output pulse time register for output 0 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 0 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 1 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 1 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 2 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 2 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 3 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 3 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 4 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 4 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 5 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 5 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 6 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 6 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 7 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 7 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 8 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 8 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 9 MSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for output 9 LSB This is the pulse time for the each output expressed in seconds. This can be used to make an output turn on and off with a certain preset interval. The min pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n To start a pulse sequence first write the pulse time to this register and then set the corresponding bit in the output status register to start the output. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw // * * * Output protection * * * Output protection time register for output 0 MSB This is the output protection time. An output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 0 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 1 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 1 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 2 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 2 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 3 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 3 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 4 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 4 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 5 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 5 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 6 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 6 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 7 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 7 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 8 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 8 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 9 MSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw Output protection time register for output 9 LSB This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output. rw /////////////////////////////////////////////////////////////////////// // Register Page 2 - Decision Matrix /////////////////////////////////////////////////////////////////////// Decision matrix row 0: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 0: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Sub zone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 0: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 0: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of thsi decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 0: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 0: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 0: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 0: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 1: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 1: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/subzone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Sub zone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 1: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 1: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 1: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 1: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 1: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 1: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 2: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 2: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Sub zone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 2: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 2: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 2: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 2: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 2: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 2: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 3: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 3: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Subzone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 3: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 3: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 3: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 3: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 3: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 3: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 4: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 4: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Sub zone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 4: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 4: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 4: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 4: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 4: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 4: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 5: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 5: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/sub zone of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Subzone match If set to one subzone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 5: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 5: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 5: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 5: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 5: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 5: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 6: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 6: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/subzone one of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Subzone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decison matrix row. Decision matrix row 6: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 6: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 6: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 6: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 6: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 6: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Decision matrix row 7: Oaddr Originating address. Set to nickname for node that should trigger action. Oaddr is the originating address. We are only interested in messages from the node given here. 0x00 is segment controller and 0xff is a node without a nickname. If bit 6 of flags is set oaddr will not be checked and events from all nodes will be accepted. rw Decision matrix row 7: flags Flags. Set selection behaviour.\n The enable bit can be used to disable a decision matrix row while it is edited.\n The zone and use sub zone bits can be activated to have a check on the zone/sub zone information of an event. That is the zone/subzone one of the machine must match the one of the event to trigger the DM row. rw Class filter bit 8 Defines the ninth bit of the class filter. Class mask bit 8 Defines the ninth bit of the class mask. Reserved bit This bit is not used. Sub zone match If set to one sub zone should be matched to trigger DM entry action. Zone match If set to one zone should be matched to trigger DM entry action. Hard coded If set to one the originating address should be hard coded to trigger DM entry action. Check Originating address If set to one the originating address should be checked and match to trigger DM entry action. Enable Enable (1) or disable (0)the decision matrix row. Decision matrix row 7: Class mask (low eight bits) The lowest eight bits of the class mask that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class mask is stored in bit 1 of the flag byte. rw Decision matrix row 7: Class filter (low eight bits) The lowest eight bits of the class filter that defines the events that should trigger the action of this decision matrix row.\n Bit 8 of the class filter is stored in bit 1 of the flag byte. rw Decision matrix row 7: Type mask Type mask that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 7: Type filter Type filter that defines the events that should trigger the action of this decision matrix row. rw Decision matrix row 7: Action This is the action or operation that should be performed if the filtering is satisfied. Only action code 0x00 is predefined and means No-Operation. All other codes are application specific and typical application defined codes could do measurement, send predefined event etc. rw Decision matrix row 7: Action parameter A numeric action parameter can be set and its meaning is application specific. rw Output pulse time register for channel 0 This is the pulse time for output 0 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 1 This is the pulse time for output 1 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 2 This is the pulse time for output 2 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 3 This is the pulse time for channel 3 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 4 This is the pulse time for channel 4 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 5 This is the pulse time for channel 5 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 6 This is the pulse time for channel 6 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 7 This is the pulse time for channel 7 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 8 This is the pulse time for channel 8 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output pulse time register for channel 9 This is the pulse time for channel 9 expressed in seconds. It can be used to have an output turn on and off with a certain preset interval. The min. pulse time is 1 second and the max time is 65535 seconds which is about 18 hours. Set to zero (default) for no pulse time i.e. the output will be steady on/off.\n\n To start a pulse sequence first write the pulse time to this register and then write to output status register to start the output sequence. The pulse train is terminated by writing on or off (1 or 0) to the output status register.\n rw Output protection time register channel 0 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 1 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 2 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 3 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 4 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 5 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 6 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 7 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 8 This is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Output protection time register channel 9 TThis is the output protection time. A output will be inactivated if not written to before this time has elapsed.\n\n Set to zero to disable (default). The max time is 65535 seconds which is about 18 hours.\n\n The registers can be as an example be used as a security feature to ensure that an output is deactivated after a preset time even if the controlling device failed to deactivate the output.\n rw Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Reserved Reserved. Low alarm An input bit has gone low and the alarm condition for it is enabled. High alarms An input bit has gone high and the alarm condition for it is enabled. Protection timer elapsed A protection timer has elapsed. 1 8 NOOP No operation Set output of I/O channel high Set the output of the I/O channel given by the argument to its high state. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9.\n Channel to set state high on Integer representing I/O channel to set state high on. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Set output of I/O channel low Set the output of the I/O channel given by the argument to its low state. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9.\n Channel to set state low on Integer representing I/O channel to set state low on. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Turn on pulse on output I/O channel Turn on pulse output on the output I/O channel given by the argument. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9. Does not have any meaning for a channel set as input.\n Channel to activate pulse output on. Integer representing I/O channel to pulse. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Turn off pulse on output I/O channel Turn off pulse output on the output I/O channel given by the argument. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9. Does not have any meaning for a channel set as input.\n Channel to activate pulse output on. Integer representing I/O channel to pulse. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Toggle output for channel Toggle output four output I/O channel given by argument. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9. Does not have any meaning for a channel set as input.\n Output I/O channel to toggle Integer representing output I/O channel to toggle. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Send status for I/O channel Send status for an I/O channel given by the argument. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9.\n For a channel set as output the status is the output applied and for a channel set as input the actual input state. Channel to send status for Integer representing the I/O channel to send status for. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 Send status for all I/O channels. Send status for all I/O channels starting with channel 0 and then taking each channel up to channel 9. Not used Not used. Send short pulse on I/O channel Send a short pulse on the I/O channel given by the argument. The argument is an integer where 0 is output 0 and so on and can be in the range 0-9.\n Register 0:47 set the pulse duration time. Channel to send status for Integer representing the I/O channel to send status for. Channel 0 I/O channel 0 Channel 1 I/O channel 1 Channel 2 I/O channel 2 Channel 3 I/O channel 3 Channel 4 I/O channel 4 Channel 5 I/O channel 5 Channel 6 I/O channel 6 Channel 7 I/O channel 7 Channel 8 I/O channel 8 Channel 9 I/O channel 9 On Event An I/O channel has been set to its ON position. For an output this means that it has been set high. For a channel set as an input it means the channel input turned high. The channel is checked every second for a change. 4 Index Contains the channel(0-9). Zone Is set to the zone for the module. Sub zone Is set to the sub zone for the channel. Off Event An I/O channel has been set to its OFF position. For an output this means that it has been set low. For a channel set as an input it means the channel input turned low. The channel is checked every second for a change. 4 Index Contains the channel(0-9). Zone Is set to the zone for the module. Sub zone Is set to the sub zone for the channel. TurnOn Event An I/O channel has been set to its ON position. The channel is checked every second for a change. This is only valid for a channel configured as input. 4 Index Contains the channel(0-9). Zone Is set to the zone for the module. Sub zone Is set to the sub zone for the channel. TurnOff Event An I/O channel has been set to its OFF position. The channel is checked every second for a change. This is only valid for a channel configured as input. 4 Index Contains the channel(0-9). Zone Is set to the zone for the module. Sub zone Is set to the sub zone for the channel. I/O Data event Input/Output data steam event sent on regular intervals if activated. 4 Data coding Set to zero for bit coding, unit=0, sensor=0. Outputs states State for outputs. Bit 0 is output 0 and so on. Input states State for inputs. Bit 0 is input 0 and so on. I/O alarm event If an alarm is armed this event is sent when it occurs and the corresponding alarm bit is set in the alarm register. 4 Index Channel where the alarm ocured. Zone Zone for module. Sub zone Sub zone for channel or sub zone for module if channel sub zone is zero. Blink channel 0 Set channel 0 to output and blink with 10 Hz. input Beijing I/O node With what frequency should channel blink?